Убил 2 телефона Nokia 6303c Cyclone Box или косяк в прищепке.
Пропаял прищепку (адаптер универсальный F-Bus UFCv2 BX для телефонов Nokia 25 кабелей ) после всего но телефоны так и не определяются. Стала как то работать по другому.
Народ помогите! Я недавно стал изучать как же программировать телефоны, из за необходимости, пришлось, коллега ушёл который этим занимался. У меня Cyclone Box с последней версией ПО и прошивкой бокса, есть два аппарата, после моих экспериментов вот они собственно :Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.1.713
Establishing Connection with Box in Main Mode...
Handling device: [Cyclone Team], [Cyclone Bootloader], [Platform: Classic]
Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic]
Initializing box...
V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C000723C
2009, wk23 / wk19
Initializing security card...
Card Serial Number: D00D04E0
Card Firmware Revision: 010A
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 4,95v PASSED
MCU Voltage 3,30v PASSED
Core Voltage 1,79v PASSED
VBAT Voltage 0,98v PASSED
VBAT Voltage 4,83v PASSED
Box VPP disabled
VPP Voltage 0,00v PASSED
Internal Box VPP Enabled
VPP Voltage 4,88v PASSED
Box VPP disabled
VPP Voltage 0,02v PASSED
External Box VPP Enabled
VPP Voltage 0,04v FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Avaiable Physical Memory: 1.141GB
Avaiable Virtual Memory: 1.886GB
Avaiable Pagefile: 2.153GB
Initializing FBUS...
All initialized - Ready to work
MCU Version V 10.12
MCU Date 08-04-10
Product RM-443 (Nokia 6303 classic)
Manufacturer (c) Nokia
IMEI 123456789012345
Mastercode 7131152510
IMEI Spare 1A23456789012345
IMEI 1234567890123456F5000000 (ИЗМЕНИЛ НАМЕРЕННО)
PPM V 10.12, 08-04-10, RM-443, (c) Nokia , I
CNT Content: i_ru_illuvial, V 10.12, 08-04-10, RM-443, (c) Nokia ,
PSN DQH607372
Product Code 0583562
Module Code 0204197
Basic Product Code 0575069
PSD 0000000000000000
LPSN 0
RETU 15
TAHVO 22
AHNE 30
HW 1000
RFIC 0831
DSP ICPR81_09w37
LCD SHARP
BT 410B-v190
Failed to read info -> Failed to read SP info
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Simlock Store not supported, not a PA_SL2 Phone
Trying to store WMDRM RPL...
Reading Keys...
Failed to read WMDRM Key
Reading Security Block...
443_353199030798592_14.10.2012_14815.SecurityBlock .PM"
read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 0D50010FD45B7D56A291AFE7C6F212B74E0384B4
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.30.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
Exploiting - running preloader...
Preloader running OK, Running Custom Loader...
Custom loader running OK! Working...
Old Loader Detected
Readed OK, Saving to "0D50010FD45B7D56A291AFE7C6F212B74E0384B4.C000 723C "
Storing Additional Data...
Checking Superdongle Key...
Section Not Found (SL3 phone?)
Checking CMLA Key...
Not Found (SL3 phone?)
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 0D50010FD45B7D56A291AFE7C6F212B74E0384B4
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E8E6E2AB6C2D394BC82633D2B4965E7E519E2FB2
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
CMT PARTNERC Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm443__08.90.mcusw (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 0D50010FD45B7D56A291AFE7C6F212B74E0384B4
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm443__08.90.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E8E6E2AB6C2D394BC82633D2B4965E7E519E2FB2
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x0001FFFF, NOR
EraseArea[0,CMT]: 0x00040000-0x0005FFFF, NOR
EraseArea[0,CMT]: 0x00060000-0x0007FFFF, NOR
EraseArea[0,CMT]: 0x00080000-0x0015FFFF, NOR
EraseArea[0,CMT]: 0x00160000-0x0023FFFF, NOR
EraseArea[0,CMT]: 0x01740000-0x0191FFFF, NOR
EraseArea[0,CMT]: 0x00240000-0x0173FFFF, NOR
EraseArea[0,CMT]: 0x022E0000-0x0261FFFF, NOR
Waiting 320s for erasure finish...
Erase taken 106.422s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT NOLO Certificate...
Block Write Failed -> Failed to write CMT cert data (3), Programming Status Error
Processing Flash Image Failed -> Failed to write all blocks
Failed to Process all Image files -> Failed to process rm443__08.90.mcusw
Failed to set Normal Mode -> Mode not accepted
Failed to set Local Mode -> Mode not accepted
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Prepare phone failed with message -> Failed to Boot CMT
Failed to Create RPL from phone -> Failed to Boot / Prepare Phone
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm443__08.90.mcusw (CMT)...
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process rm443__08.90.mcusw
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Proceeding with Recovery Mode...
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Prepare phone failed with message -> Failed to Boot CMT
Recovery Mode Failed, storing Certificates Only
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Prepare phone failed with message -> Failed to Boot CMT
Failed to Create RPL from phone -> Failed to Boot / Prepare Phone
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm443__08.90.mcusw (CMT)...
Booting CMT...
Sending User Abort Signal...
CBUS Request Error -> User abort
Failed to Boot CMT -> No answer from CBUS
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process rm443__08.90.mcusw
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Prepare phone failed with message -> Failed to Boot CMT
Failed to Check BB5 Flashing Bus -> Failed to Boot / Prepare Phone
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Prepare phone failed with message -> Failed to Boot CMT
Failed to Create RPL from phone -> Failed to Boot / Prepare Phone
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm443__08.90.mcusw (CMT)...
Booting CMT...
Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process rm443__08.90.mcusw
Sending User Abort Signal...
Phone not detected at USB -> User Abort
Failed to read info -> Phone not detected
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Sending User Abort Signal...
Phone not detected at USB -> User Abort
Proceeding with Recovery Mode...
Booting CMT...
Sending User Abort Signal...
Sending User Abort Signal...
BB5 USB Boot Rom not Detected -> Timeout, no any compatible USB device detected.
Failed to Boot CMT -> No compatible USB devices detected
Prepare phone failed with message -> Failed to Boot CMT
Recovery Mode Failed, storing Certificates Only
Booting CMT...
Sending User Abort Signal...
BB5 USB Boot Rom not Detected -> User Abort
Failed to Boot CMT -> No compatible USB devices detected
Prepare phone failed with message -> Failed to Boot CMT
Failed to Create RPL from phone -> Failed to Boot / Prepare Phone
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Selecting USB Flashing Method...
Proceeding with Dead USB Mode
Press power-on shortly to run USB Boot ROM
Sending User Abort Signal...
BB5 USB Boot Rom not Detected -> User Abort
Failed to prepare BB5 USB Connection -> USB Boot ROM Not detected, timeout
Failed to Process all Image files -> Failed to prepare BB5 USB Flashing
Телефоны перестали определятся, :-) , что я не так сделал и как это исправить ПОМОГИТЕ!
Ответить с цитированием
