6300 contact cervice

[GSM_master]

При вкл. пишет contact cervice и выкл. Прошил фениксом все прошился заработал выкл. вкл. и опять contact cervice. Шью цыклоном ппм не пролевает

инфа

Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm217__07.30.mcusw (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 1990020303556C56878A545DE4165CA016EF59BA
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm217__07.30.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x00EC220800006921, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2208 (Samsung), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7F7E6491E8D30494B45630BB3A8599F4E1C674C9
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x000006BF, NOR
EraseArea[0,CMT]: 0x000006C0-0x0001FFFF, NOR
EraseArea[0,CMT]: 0x00020000-0x0007FFFF, NOR
EraseArea[0,CMT]: 0x00080000-0x000DFFFF, NOR
EraseArea[0,CMT]: 0x00100000-0x001FFFFF, NOR
EraseArea[0,CMT]: 0x00200000-0x0031FFFF, NOR
EraseArea[0,CMT]: 0x00320000-0x0105FFFF, NOR
EraseArea[0,CMT]: 0x01060000-0x01067FFF, NOR
EraseArea[0,CMT]: 0x01068000-0x0107FFFF, NOR
Waiting 320s for erasure finish...
Erase taken 40.187s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT NOLO Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT UPDAPP Certificate...
Writing CMT DSP0 Certificate...
Writing CMT MCUSW Certificate...
Writing CMT PMM_CONF Certificate...
Writing CMT SBIF_CONF Certificate...
Programming Status OK!
All blocks written OK! Time taken 80.781s
Flashing Speed: 1505,72 kBit/S
Restarting MCU...
Processing rm217__07.30.mcusw (APE)...
Processing rm217__07.30.ppm_c (CMT)...
Image File Parse Failed -> Data checksum failed at 0x40B9
Processing Flash Image Failed -> Failed to parse Image File
Failed to Process all Image files -> Failed to process rm217__07.30.ppm_c

[kurgan93]

попробуйте ррм от 7.21

[Jaha]

Прошивайте 7.21 и симлок проверьте и проложите лог MX-key

[GSM_master]

попробуйте ррм от 7.21

Вроде помагло,пока работает!

[dissident]

Вроде помагло,пока работает!

Если захочите поставить версию прошивки 7.30, советую почитать здесь http://www.unlockers.ru/threads/4141...l=1#post234809 , пост №13

[БСА1]

Прошивал несколько раз телефон в таком порядке
заливаете файл rm217__07.30.mcusw,а ppm и image версией 7.21. Проверено все работает .PM заливал с рабочего телефона .Прошивал UFS и ATF.