Нужен фулл для Nokia N95 (MT6225A)

[Sammuel]

Привет всем !
Есть тело Nokia N95 ! Подключили другое зарядник и он умер . При вкл БП определял 0,66А, разбырал греелся проц MT6225A, поменял на новую и телефон перестал греется ! Сечяс для него нужен фулл с русским !
Повтаряю процессор MT6225A, а не MT6226,

С инфинити читал фул флеш



COM7 [VCP0] selected

Device: Autodetect 6205-6227 NOR

Checking data, wait...

advanced flash detection enabled

eeprom backup enabled, it may takes several minutes !

Action: read NOR flash

Boot...

Press and HOLD Power button now !

19200 fixed

Connecting, wait...

Initializing[6225:8A03:8A00]...

CPU: MT6225

high speed boot enabled

chip: 0001:D903:0004

boot step size: 0400

Release Power button now !

Boot Done

Initialize...

detecting chip #00 in region #00...

flash: 01027E02200200:18C59F00000000

flash: AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb

detecting chip #01 in region #00...

flash: 01027E02200200:18C59F00000000

flash: AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb

number of flash chip/regions detected: 02/01

Initialize Done

Set baud...

230400

Set baud Done

Initialize bootcode...

Initialize bootcode Done

Check firmware integrity...

device parameters autodetection in progress..

detecting chip #00 in region #00...

flash: 01027E02200200:18C59F00000000

flash: AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb

detecting chip #01 in region #00...

flash: 01027E02200200:18C59F00000000

flash: AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb

it's time to stop: 18C09FC518C09FC518C09FC518C09FC518C09FC518C09FC5

number of flash chip/regions detected: 01/01

total flash region size: 01000000

detect device identification#1...

detection phase #1...

.

detection phase #2...

.................................................. .................................................. ............................

warning: identification#1 information not found, possible reasons:

.old firmware type w/o identification#1 data

.damaged firmware

.damaged hardware

if phone works fine just ignore this warning

detect device identification#1 finished

detect device identification#2...

detection phase #1...

.

warning: optional information not found,

if phone works well just ignore this warning

detect device identification#2 finished

detecting eeprom/ffs area in 1 chip(s)...

standard eeprom/ffs offset assigned: 00E00000

flash: 01027E02200200:18C59F00000000

checking area[00000000]: 00000000-00FFFFFF...

Can't detect eeprom/ffs area

Do you want to use standard ffs address: 00E00000 ?



If you are not sure that standard address is correct:

1. press "NO" and terminate current operation

2. make flash backup for emergency case

3. repeat required operation

standard ffs address selected by user

detecting eeprom/ffs size...

eeprom/ffs size: 00200000

ffs chip: 00

eeprom/ffs area: 00000000:00E00000-00FFFFFF

Check firmware integrity Done

Check firmware content...

Check firmware content Done

Backup required data...

reading [flash]...

file saved: C:\Documents and Settings\Samuel\Desktop\backup_flash_20090304-190603.B0M.bin

Finished, time used: 1375 sec

Remove/Install battery now !


9622 9623 9624