Maps77
06.01.2014, 16:44
Device synchronized.
Injecting EBL-Loader (RPSI).
Injecting EBL
Boot-loader is active
EBL version: 2150_OD_KH2_3.1 3..1
Boot mode is: BB
Using: Faster CRC, Writing all blocks , Skip data CRC , Skip protocol CRC
Package length is 16384 - protocol: 3.32
Baud rate set to 921600
Get flash id.
Flash ID is: 003000EC
Boot process finished
Start downloading item 'CUST:temp_GT-C3332_OXE.dffs'' from file 'C:\Documents and Settings\maps77\Мои документы\Downloads\123\C3332XEKK3\C3332OXEKK1_CSC .dffs''.
Sending sec-pack.
Load region 0
- Sending data.
Process time was 32.0 sec.
Stopped at 0% total, 1% current
Timeout occured during packet reception
The phone did not answer within the timeout period. This could be that the communication is interrupted or that the target SW is in an endless loop.
Check the connection to the phone, battery etc. If the problem persists report the error to the developer.
Channel 1 is succesfully closed.
Вот что показывает мне лог. Шью обычным УСБ. Есть вопрос:- какая распиновка у этого зверя? Есть кабель на чипе ПЛ 2303 и руки не из пятой точки (уже переделывал, шил и форматил Китов и других производителей) может есть вариант заставить ентот ап-ат фунциклировать? А то выкидывать жалко, а орехи колоть он маловат.Буду признателен за помощь и критику. С новым годом Всех!
P.S. у него *инфинити* платформа, мож лучше создать раздел под эту платформу?
Injecting EBL-Loader (RPSI).
Injecting EBL
Boot-loader is active
EBL version: 2150_OD_KH2_3.1 3..1
Boot mode is: BB
Using: Faster CRC, Writing all blocks , Skip data CRC , Skip protocol CRC
Package length is 16384 - protocol: 3.32
Baud rate set to 921600
Get flash id.
Flash ID is: 003000EC
Boot process finished
Start downloading item 'CUST:temp_GT-C3332_OXE.dffs'' from file 'C:\Documents and Settings\maps77\Мои документы\Downloads\123\C3332XEKK3\C3332OXEKK1_CSC .dffs''.
Sending sec-pack.
Load region 0
- Sending data.
Process time was 32.0 sec.
Stopped at 0% total, 1% current
Timeout occured during packet reception
The phone did not answer within the timeout period. This could be that the communication is interrupted or that the target SW is in an endless loop.
Check the connection to the phone, battery etc. If the problem persists report the error to the developer.
Channel 1 is succesfully closed.
Вот что показывает мне лог. Шью обычным УСБ. Есть вопрос:- какая распиновка у этого зверя? Есть кабель на чипе ПЛ 2303 и руки не из пятой точки (уже переделывал, шил и форматил Китов и других производителей) может есть вариант заставить ентот ап-ат фунциклировать? А то выкидывать жалко, а орехи колоть он маловат.Буду признателен за помощь и критику. С новым годом Всех!
P.S. у него *инфинити* платформа, мож лучше создать раздел под эту платформу?