Nokia 2700 через раз включается.

[Jackson777]

Принесли тел с диагнозом не работает. Прошил UFS включился и нормально работал. Потом выключился и всё. Фениксом не прошивается до конца. UFS шьёт но так же работает немного а потом выключается. И при этом включается через раз.
Вот лог
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia/Blackberry Application v01.64, (Jun 30 2011 15:31:22, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2011
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C0004DA0
HW Revision: B, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2010, wk35
Initializing security card...
Card Serial Number: *******
Card Firmware Revision: 010A
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5,03v PASSED
MCU Voltage 3,29v PASSED
Core Voltage 1,80v PASSED
VBAT Voltage 1,51v PASSED
VBAT Voltage 4,93v PASSED
Box VPP disabled
VPP Voltage 0,04v PASSED
Internal Box VPP Enabled
VPP Voltage 5,01v PASSED
Box VPP disabled
VPP Voltage 0,04v PASSED
External Box VPP Enabled
VPP Voltage 0,04v FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
Initializing FBUS...
All initialized - Ready to work
Failed to read info -> Phone not detected
Failed to read info -> Phone not detected
MCU Version V 09.97
MCU Date 18-06-10
Product RM-561 (Nokia 2700 classic)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452351F4000000
PPM V 09.97, 18-06-10, RM-561, (c) Nokia , EL
CNT Content: el_red, V 09.97, 18-06-10, RM-561, (c) Nokia ,
PSN DAW006658
Product Code 0587976
Module Code 0204245
Basic Product Code 0577212
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 1000
RFIC 06540601
DSP ICPR72_09w26
LCD SEIKO
BT 2222-302
Failed to read info -> Failed to read SP info

[sanya08]

пробуй другой акб,версию прошывки другую после прошывки делай сброси и потребление от бп какое?

[ermak72]

В логе IMEI 12345610654321?
Это ни о чём не говорит?

[Jackson777]

О а я этого не заметил. И что теперь RPL заказывать???

[flashmax]

Если бекапов нет, то только рпл.

[Jackson777]

Есть бекап. Оказалось самый первый был с нормальный imei. Вот
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia/Blackberry Application v01.64, (Jun 30 2011 15:31:22, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2011
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: *******
HW Revision: B, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2010, wk35
Initializing security card...
Card Serial Number: D0030062
Card Firmware Revision: 010A
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5,00v PASSED
MCU Voltage 3,29v PASSED
Core Voltage 1,80v PASSED
VBAT Voltage 1,45v PASSED
VBAT Voltage 4,93v PASSED
Box VPP disabled
VPP Voltage 0,04v PASSED
Internal Box VPP Enabled
VPP Voltage 5,01v PASSED
Box VPP disabled
VPP Voltage 0,02v PASSED
External Box VPP Enabled
VPP Voltage 0,02v FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Super DCT4 Activation: TRUE
Initializing FBUS...
All initialized - Ready to work
MCU Version V 09.97
MCU Date 18-06-10
Product RM-561 (Nokia 2700 classic)
Manufacturer (c) Nokia
IMEI 353394046071221
Mastercode 6561655646
IMEI Spare 3A35930464702102
IMEI SV 3335930464702152F4000000
PPM V 09.97, 18-06-10, RM-561, (c) Nokia , EL
CNT Content: el_red, V 09.97, 18-06-10, RM-561, (c) Nokia ,
PSN DAW006658
Product Code 0587976
Module Code 0204245
Basic Product Code 0577212
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 1000
RFIC 06540601
DSP ICPR72_09w26
LCD SEIKO
BT 2222-302
Failed to read info -> Failed to read SP info

[Jackson777]

Вот щас MCU Version V 09.97
MCU Date 18-06-10
Product RM-561 (Nokia 2700 classic)
Manufacturer (c) Nokia
IMEI 353394046071221
Mastercode 6561655646
IMEI Spare 3A35930464702102
IMEI SV 3335930464702152F4000000
PPM V 09.97, 18-06-10, RM-561, (c) Nokia , EL
CNT Content: el_red, V 09.97, 18-06-10, RM-561, (c) Nokia ,
PSN DAW006658
Product Code 0587976
Module Code 0204245
Basic Product Code 0577212
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 1000
RFIC 06540601
DSP ICPR72_09w26
LCD SEIKO
BT 2222-302
Simlock Server SIMLOCK SERVER
Simlock Key 2440700000000000
Simlock Profile 0000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [1,2] State: OPENED Type: GID Data: FFFF
Simlock [1,3] State: OPENED Type: GID Data: FFFF
Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [2,2] State: OPENED Type: GID Data: FFFF
Simlock [2,3] State: OPENED Type: GID Data: FFFF
Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [3,2] State: OPENED Type: GID Data: FFFF
Simlock [3,3] State: OPENED Type: GID Data: FFFF
Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [4,2] State: OPENED Type: GID Data: FFFF
Simlock [4,3] State: OPENED Type: GID Data: FFFF
Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [5,2] State: OPENED Type: GID Data: FFFF
Simlock [5,3] State: OPENED Type: GID Data: FFFF
Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [6,2] State: OPENED Type: GID Data: FFFF
Simlock [6,3] State: OPENED Type: GID Data: FFFF
Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [7,2] State: OPENED Type: GID Data: FFFF
Simlock [7,3] State: OPENED Type: GID Data: FFFF
Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
нормальный вроде но тел не включается. При попытке включить один раз срабатывает вибра и больше ничего не происходит.

[Jackson777]

Я его и прошил и бекап RPL залил но всё так же. Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm561__09.97.mcusw (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 20D00016651E00562967F9CB1BF7AAD89B5DEDBD
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC: 273F6D55
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm561__09.97.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 3EA22A1DDA660002E56108DB5072A10F8709443F
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x000006BF, NOR
EraseArea[0,CMT]: 0x000006C0-0x0001FFFF, NOR
EraseArea[0,CMT]: 0x00040000-0x000BFFFF, NOR
EraseArea[0,CMT]: 0x000C0000-0x0013FFFF, NOR
EraseArea[0,CMT]: 0x00140000-0x0137FFFF, NOR
EraseArea[0,CMT]: 0x01380000-0x0151FFFF, NOR
Waiting 320s for erasure finish...
Erase taken 88.47s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT NOLO Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT UPDAPP Certificate...
Writing CMT DSP0 Certificate...
Writing CMT MCUSW Certificate...
Programming Status OK!
All blocks written OK! Time taken 67.18s
Flashing Speed: 2429,24 kBit/S
Restarting MCU...
Processing rm561__09.97.mcusw (APE)...
Processing rm561__09.97.ppm_el (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 20D00016651E00562967F9CB1BF7AAD89B5DEDBD
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC: 273F6D55
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm561__09.97.ppm_el, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 3EA22A1DDA660002E56108DB5072A10F8709443F
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x01520000-0x01DBFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 23.244s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 18.564s
Flashing Speed: 2310,31 kBit/S
Restarting MCU...
Processing rm561__09.97.ppm_el (APE)...
Processing rm561__09.97.image_el_blac (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 20D00016651E00562967F9CB1BF7AAD89B5DEDBD
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC: 273F6D55
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm561__09.97.image_el_blac, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 3EA22A1DDA660002E56108DB5072A10F8709443F
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x01DC0000-0x0215FFFF, NOR
EraseArea[0,CMT]: 0x02160000-0x03FBFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 73.211s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 35.537s
Flashing Speed: 2540,56 kBit/S
Restarting MCU...
Processing rm561__09.97.image_el_blac (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version V 09.97
MCU Date 18-06-10
Product RM-561 (Nokia 2700 classic)
Manufacturer (c) Nokia
IMEI 353394046071221
Mastercode 6561655646
IMEI Spare 3A35930464702102
IMEI SV 3335930464702152F4000000
PPM V 09.97, 18-06-10, RM-561, (c) Nokia , EL
CNT Content: el_black, V 09.97, 18-06-10, RM-561, (c) Nokia ,
PSN DAW006658
Product Code 0587976
Module Code 0204245
Basic Product Code 0577212
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 1000
RFIC 06540601
DSP ICPR72_09w26
LCD SEIKO
BT 2222-302
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
MCU Version V 09.97
MCU Date 18-06-10
Product RM-561 (Nokia 2700 classic)
Manufacturer (c) Nokia
IMEI 353394046071221
Mastercode 6561655646
IMEI Spare 3A35930464702102
IMEI SV 3335930464702152F4000000
PPM V 09.97, 18-06-10, RM-561, (c) Nokia , EL
CNT Content: el_black, V 09.97, 18-06-10, RM-561, (c) Nokia ,
PSN DAW006658
Product Code 0587976
Module Code 0204245
Basic Product Code 0577212
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 1000
RFIC 06540601
DSP ICPR72_09w26
LCD SEIKO
BT 2222-302
Failed to read info -> Failed to read SP info

[Archie Rostov]

Вскройте аппарат у вас скорее всего сидит водичка в районе дисплейного разъёма !!!
Так ,что вы зашейтесь ни чего не выдет !
и Выложите вы наконец Self test от UFS!!!

[Jackson777]

Плата абсолютно чистая
1ST BOOT : C0,07 [] [2.2.0.1]
CMT ASICID: 000000010000022600010006030C192101033000
EM 1 ID : 00000296
EM 2 ID : 00000B22
CMT PUBID : 20D00016651E00562967F9CB1BF7AAD89B5DEDBD
CMT MODE : 00
CMT HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROMID : 273F6D55DFAAF68F
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv3_2nd.fg, Ver: 9.11.1
CMT FLID0 : 00EC2400-00008A31, Sam K8x1259ETF
CMT FLCNT : 00000000000000000000000000000000000000
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO : RAP3Gv3_algo.fg, Ver: 9.17.0
CMT KSIG0 : 3EA22A1DDA660002E56108DB5072A10F8709443F
CMT VPP : Internal
DUAL LINE : True
CMT ALG Boot OK
PASUBTOC : PA_SL3
Rebooting Mobile

Он в локал не входит. Не могу селф тесты выложить.

[dissident]

RETU,TAHVO прогрейте феном с нижним подогревом, тел должен включитса.

[flashmax]

Смотрите цепь BSI.

[neonovec]

Шей последнюю версию прошивки . если стояла последняя то тогда поиграй с резюками на БСИ чтобы в локал мод загнать резисторы 3,3 /5,1/ 7,5 тебе надо зброс ему зделать на все галочки

[Errorkey]

Попробуй слить и залить обратно RPL (хотя ты получается это уже делал)
Direct Unlock а потом sx4 авторизацию